1 | // plow_main.c |
2 | // Main logic controller for the snow plow |
3 | // Copyright (c) Joshua 'joshuas3' Stockin 2020 |
4 |
|
5 | #include "plow_main.h" |
6 | #include "pulseIn.h" |
7 | #include "util.h" |
8 |
|
9 | #include <stdio.h> |
10 |
|
11 | #include "esp_system.h" |
12 | #include "esp_task_wdt.h" |
13 | #include "freertos/FreeRTOS.h" |
14 | #include "freertos/task.h" |
15 | #include "driver/gpio.h" |
16 | #include "driver/uart.h" |
17 |
|
18 | static void onrestart(void) { |
19 | gpio_set_level(STATUS_RED, HIGH); |
20 | delay(250); |
21 | } |
22 |
|
23 | static int ping_count = 1; |
24 | static void pingTask(void * pingOK) { |
25 | configASSERT(((bool)pingOK) == true); |
26 | static int beeps; |
27 | static int i; |
28 | for (;;) { |
29 | delay(3000); |
30 | printf("ping #%dx%d: %i ticks\n", ++beeps, ping_count, xTaskGetTickCount()); |
31 | for (i = 0; i < ping_count; i++) { |
32 | gpio_set_level(STATUS_YELLOW, HIGH); |
33 | delay(0200); |
34 | gpio_set_level(STATUS_YELLOW, LOW); |
35 | delay(0200); |
36 | } |
37 | } |
38 | } |
39 |
|
40 | const int uart_blade_control = UART_NUM_1; |
41 | const int uart_motor_control = UART_NUM_2; |
42 | static void radioTask(void * arg) { |
43 | configASSERT(((bool)arg) == true); |
44 | unsigned int R1; |
45 | unsigned int R2; |
46 | unsigned int R3; |
47 | unsigned int R4; |
48 | unsigned int R5; |
49 | unsigned int R6; |
50 | unsigned char SWITCH_MOTORS = 0; |
51 | unsigned char SWITCH_SALT = 0; |
52 | for (;;) { |
53 | R1 = pulseIn(RADIO_1, true); |
54 | R2 = pulseIn(RADIO_2, true); |
55 | R3 = pulseIn(RADIO_3, true); |
56 | R4 = pulseIn(RADIO_4, true); |
57 | R5 = pulseIn(RADIO_5, true); |
58 | R6 = pulseIn(RADIO_6, true); |
59 | if (R1 || R2 || R3 || R4 || R5 || R6) { |
60 | ping_count = 2; |
61 | unsigned int R1m = map(R1, 160000, 320000, 0, 1000); // right horizontal |
62 | unsigned int R2m = map(R2, 160000, 320000, 0, 1000); // right vertical |
63 | unsigned int R3m = map(R3, 160000, 320000, 0, 1000); // left vertical |
64 | unsigned int R4m = map(R4, 160000, 320000, 0, 1000); // left horizontal |
65 | unsigned char R5m = map(R5, 160000, 320000, 0, 1000)>500; |
66 | unsigned char R6m = map(R6, 160000, 320000, 0, 1000)>500; |
67 |
|
68 | // Switches |
69 | if (SWITCH_SALT != R6m) { |
70 | printf("salt spreader switch flip\n"); |
71 | SWITCH_SALT = R6m; |
72 | gpio_set_level(SOLENOID_SALT, !R6m); |
73 | } |
74 | if (SWITCH_MOTORS != R5m) { |
75 | printf("motors switch flip\n"); |
76 | SWITCH_MOTORS = R5m; |
77 | if (R5m) { |
78 | gpio_set_level(BATTERY_MOTORCONTROL, !R5m); |
79 | gpio_set_level(BATTERY_BLADECONTROL, !R5m); |
80 | delay(200); |
81 | gpio_set_level(SOLENOID_MOTORS, !R5m); |
82 | } else { |
83 | gpio_set_level(SOLENOID_MOTORS, !R5m); |
84 | delay(200); |
85 | gpio_set_level(BATTERY_MOTORCONTROL, !R5m); |
86 | gpio_set_level(BATTERY_BLADECONTROL, !R5m); |
87 | } |
88 | } |
89 |
|
90 | // Motor controller configuration |
91 | if (R5m) { |
92 | // Blade control |
93 | unsigned int blade_pitch = 0; |
94 | unsigned int blade_yaw = 0; |
95 | if (R3m > 600) { |
96 | blade_pitch = map(R3m, 600, 1000, 192, 255); |
97 | } else if (R3m < 400) { |
98 | blade_pitch = map(R3m, 0, 400, 128, 192); |
99 | } else { |
100 | blade_pitch = 192; |
101 | } |
102 | if (R4m > 600) { |
103 | blade_yaw = map(R4m, 600, 1000, 64, 127); |
104 | } else if (R4m < 400) { |
105 | blade_yaw = map(R4m, 0, 400, 1, 64); |
106 | } else { |
107 | blade_yaw = 64; |
108 | } |
109 |
|
110 | // Motor control |
111 | unsigned char motor_left = 0; |
112 | unsigned char motor_right = 0; |
113 | if (R2m > 600) { |
114 | motor_left = map(R2m, 600, 1000, 64, 127); |
115 | motor_right = map(R2m, 600, 1000, 192, 255); |
116 | } else if (R2m < 400) { |
117 | motor_left = map(R2m, 0, 400, 1, 64); |
118 | motor_right = map(R2m, 0, 400, 128, 192); |
119 | } else { |
120 | motor_left = 64; |
121 | motor_right = 192; |
122 | } |
123 | if (R1m > 600) { // right turn |
124 | motor_left = 64 + map(R1m, 600, 1000, 1, 63); |
125 | motor_right = 192 - map(R1m, 600, 1000, 1, 63); |
126 | } else if (R1m < 400) { // left turn |
127 | motor_left = map(R1m, 0, 400, 1, 63); |
128 | motor_right = 192 + (64 - map(R1m, 0, 400, 1, 63)); |
129 | } |
130 | printf("Motors:\tpitch\tyaw\tleft\tright\n"); |
131 | printf("Motors:\t%i\t%i\t%i\t%i\n", blade_pitch, blade_yaw, motor_left, motor_right); |
132 | char motor_bytes[] = {motor_left, motor_right}; |
133 | char blade_bytes[] = {blade_pitch, blade_yaw}; |
134 | uart_write_bytes(uart_motor_control, (const char*)motor_bytes, 2); |
135 | uart_write_bytes(uart_blade_control, (const char*)blade_bytes, 2); |
136 | } else { |
137 | printf("Radio RX:\t%i\t%i\t%i\t%i\t%i\t%i\n", R1m, R2m, R3m, R4m, R5m, R6m); |
138 | } |
139 | } else { |
140 | ping_count = 1; |
141 | printf("Radio RX:\t-\t-\t-\t-\t-\t-\n"); |
142 | if (SWITCH_SALT != 0) { |
143 | printf("salt spreader switch flip\n"); |
144 | SWITCH_SALT = 0; |
145 | gpio_set_level(SOLENOID_SALT, HIGH); |
146 | } |
147 | if (SWITCH_MOTORS != 0) { |
148 | printf("motors switch flip\n"); |
149 | SWITCH_MOTORS = 0; |
150 | gpio_set_level(SOLENOID_MOTORS, HIGH); |
151 | delay(200); |
152 | gpio_set_level(BATTERY_MOTORCONTROL, HIGH); |
153 | gpio_set_level(BATTERY_BLADECONTROL, HIGH); |
154 | } |
155 | } |
156 | esp_task_wdt_reset(); |
157 | delay(10); |
158 | } |
159 | } |
160 |
|
161 | void app_main(void) |
162 | { |
163 | printf("entering app_main\n"); |
164 |
|
165 | printf("configuring STATUS_[GREEN|YELLOW|RED] GPIO output\n"); |
166 | gpio_config_t io_conf; |
167 | io_conf.pin_bit_mask = (1ULL<<STATUS_GREEN) | (1ULL<<STATUS_YELLOW) | (1ULL<<STATUS_RED); |
168 | io_conf.mode = GPIO_MODE_OUTPUT; |
169 | io_conf.intr_type = GPIO_INTR_DISABLE; |
170 | gpio_config(&io_conf); |
171 |
|
172 | printf("pulling STATUS_[GREEN|YELLOW|RED] HIGH\n"); |
173 | gpio_set_level(STATUS_GREEN, HIGH); |
174 | gpio_set_level(STATUS_YELLOW, HIGH); |
175 | gpio_set_level(STATUS_RED, HIGH); |
176 |
|
177 | printf("configuring BATTERY_[MOTOR|BLADE]CONTROL, SOLENOID_[SALT|MOTORS], and RELAY_BOARD GPIO output\n"); |
178 | io_conf.pin_bit_mask = (1ULL<<SOLENOID_SALT) | (1ULL<<SOLENOID_MOTORS) | (1ULL<<BATTERY_MOTORCONTROL) | (1ULL<<BATTERY_BLADECONTROL) | (1ULL<<RELAY_BOARD); |
179 | io_conf.mode = GPIO_MODE_OUTPUT; |
180 | gpio_config(&io_conf); |
181 |
|
182 | printf("pulling all high\n"); |
183 | gpio_set_level(SOLENOID_SALT, HIGH); |
184 | gpio_set_level(SOLENOID_MOTORS, HIGH); |
185 | gpio_set_level(BATTERY_MOTORCONTROL, HIGH); |
186 | gpio_set_level(BATTERY_BLADECONTROL, HIGH); |
187 | gpio_set_level(RELAY_BOARD, HIGH); |
188 |
|
189 | printf("configuring RADIO_[1-6] GPIO input\n"); |
190 | io_conf.pin_bit_mask = (1ULL<<RADIO_1) | (1ULL<<RADIO_2) | (1ULL<<RADIO_3) | (1ULL<<RADIO_4) | (1ULL<<RADIO_5) | (1ULL<<RADIO_6); |
191 | io_conf.mode = GPIO_MODE_INPUT; |
192 | gpio_config(&io_conf); |
193 |
|
194 | printf("configuring UART\n"); |
195 | uart_config_t uart_config = { |
196 | .baud_rate = CONTROL_BAUDRATE, |
197 | .data_bits = UART_DATA_8_BITS, |
198 | .parity = UART_PARITY_DISABLE, |
199 | }; |
200 | ESP_ERROR_CHECK(uart_param_config(uart_motor_control, &uart_config)); |
201 | ESP_ERROR_CHECK(uart_param_config(uart_blade_control, &uart_config)); |
202 | ESP_ERROR_CHECK(uart_set_pin(uart_motor_control, UART_MOTOR_CONTROL, NULL_PIN, NULL_PIN, NULL_PIN)); |
203 | ESP_ERROR_CHECK(uart_set_pin(uart_blade_control, UART_BLADE_CONTROL, NULL_PIN, NULL_PIN, NULL_PIN)); |
204 |
|
205 | printf("installing UART\n"); |
206 | const int uart_buffer_size = 256; |
207 | ESP_ERROR_CHECK(uart_driver_install(uart_motor_control, uart_buffer_size, uart_buffer_size, 0, NULL, 0)); |
208 | ESP_ERROR_CHECK(uart_driver_install(uart_blade_control, uart_buffer_size, uart_buffer_size, 0, NULL, 0)); |
209 |
|
210 | printf("registering shutdown function\n"); |
211 | esp_register_shutdown_handler(onrestart); |
212 |
|
213 | printf("creating ping task\n"); |
214 | TaskHandle_t pingTaskHandle = NULL; |
215 | xTaskCreate(pingTask, "pingTask", 2000, (void *)true, tskIDLE_PRIORITY, &pingTaskHandle); |
216 |
|
217 | printf("creating radio task\n"); |
218 | TaskHandle_t radioTaskHandle = NULL; |
219 | xTaskCreate(radioTask, "radioTask", 10000, (void *)true, 1, &radioTaskHandle); |
220 |
|
221 | printf("pulling STATUS_[YELLOW|RED] LOW\n"); |
222 | gpio_set_level(STATUS_YELLOW, LOW); |
223 | gpio_set_level(STATUS_RED, LOW); |
224 | } |
225 |
|